New from Killer RC
This new "plug & play" Light Controller allows you to control multiple sets of LED headlights and tail lights on your RC car. The Killer RC Light Controller goes in between your radio receiver and your servos. Use your 3rd channel to switch through 3 headlight modes; off, low beam, and high beam. This light controller is compatible with any 3 channel radio. The Killer RC light controller can also power a set of 2 tail/brake lights. When you apply the brakes on your transmitter your tail lights will light up and become brake lights. You can also make your tail lights function as turn signals. As you steer the car the tail lights will flash which ever direction you are turning. This feature can be disabled. The Killer RC light controller also has an always-on marker light output, which can be used for UnderGlow lights or whatever you want. Connect a v2 or v2-S Killer Bee to the Aux output on the light controller, and then you can kill the engine by turning off the transmitter power. With 4 channel radios the setup is a little different, so be sure to watch the light controller videos on our video page. The Killer RC light controller can also be used with 2 channel radios but the headlights will always be constantly On until the receiver power switch is turned Off. Another cool feature we have added is that the headlights will automatically start flashing when your battery voltage gets low (4.3v), alerting you that you need to recharge the battery pack. This light controller operates on 4 to 12 volts, but whatever voltage your battery is, that is what the light controller will put out to your LED lights. Six volts is the usual application. This light controller is compact in size, doesn't get hot, and can be used on many gas, nitro, and electric RCs. The Killer RC light controller works best with Ramtech brand headlights, and Killer RC brand tail lights.
The Killer RC Light Controller can be bought in our store.
Watch these videos to see about the Killer RC Light Controller.
Watch Part 1 of the Killer RC Light ControllerHERE.
Watch Part 2 of the Killer RC Light ControllerHERE.
Watch Part 3 of the Killer RC Light ControllerHERE.
Now it's easy to add tail lights to your HPI Baja 5T using the stock light brackets. This kit uses high quality LEDs that will last for thousands of hours. These lights operate on 4 to 8.5 volts. Each light board only pulls 70ma, which means that a 3,000mAh battery could power a pair of these tail lights for over 21 hours. Includes 6 mounting screws and 6 black plastic washers to hold the circuit boards in place. The wiring is 32 inches (81cm) long. Red is the only color available for now. After installation it is a good idea to coat the back of the LED circuit board with some Shoe Goo or silicone to help protect it from water. These tail lights work perfectly with the new Killer RC Light Controller.
The 5T Tail Light Kit can be bought in our store.
Watch the install video HERE.
Power Switch
The Killer RC power switch includes a rubber dust cover.
The Power Switch can be bought in our store.
Watch the install video HERE.
6" 4-Way Splitter Cable
6" long. One male to four female. JR/Hitec style plug. Gold plated contacts. 3 conductor. 22 AWG.
The 4-Way Splitter Cable can be bought in our store.
Watch the install video HERE.
6" Y Splitter Cable
Two female, One male JR/Futaba/Hitec plug.
The Y Splitter Cable can be bought in our store.
Inline Fuse Holder
Servos and wiring can short-circuit, which can damage your expensive radio receiver, battery, and even catch the radio box on fire. The Killer RC inline fuse will prevent this. Just plug it inline between the battery and your on/off switch. Comes with 15A fuse. Works with most any gas or nitro electrical system. In the event of a blown fuse loosing battery power to the receiver can cause a runaway vehicle, so we recommend that you use a Killer Bee kill switch to stop any potential runaways.
The Inline Fuse Holder can be bought in our store.
The 6.6v 3200mAh LiFePO4 receiver battery pack has been Discontinued. Upgraded version coming soon! We are working on a new and better LiFe receiver pack. Check back here often.
Hyperion LiFeP04 Transmitter Battery Pack & Adapter Cable
These new LiFe packs are a great for powering the Futaba 4PK, 3PK, 3PM, or Airtronics M11 . If you don't have a LiFe compatible charger you can still use these packs. These LiFe packs have a built-in Protection Circuit that allows you to charge the pack with a standard NiMh wall plug charger, like the charger that comes with the Futaba 4PK. This pack comes with a Hyperion/Polyquest balance tap.
This pack features:
- More capacity per gram than NiMh.
- Almost no "self discharge", so your radio is always ready to go even weeks after charging.
- Superior voltage performance under load.
- Faster charge time.
- Safer and more convenient than LiPo.
Includes custom Killer RC adapter cable with JR/Futaba style plug.
The Hyperion 6.6v and 9.9v LiFePO4 Battery Packs for Transmitters can be bought in our store.
Hyperion Balance Board
This balance board adapter works with Hyperion/Hyperion/JST-XH balance taps on LiFe and LiPo battery packs. See this forum thread for more info on how you can use this balance board.
The Hyperion Balance Board can be bought in our store.
imaxRC B6AC Pro Balance Charger
The Imax B6 AC Pro charger is a very nice charger that will charge any type of battery pack, including NiMh, NiCd, Pb, LiFe, LiPo. It works on 100 - 250 vac wall outlet, or 12v power supply. Multi-use wires are provided with the B6AC. You can charge and discharge your battery easily with these wires.
B6AC PRO Specification:
- lnputYoltage: DC 11V-18V, AC 100V-250V
- Charge current: 0.1-5A, 0.1A step
- Discharge current 0.1-1A, 0.1A step
- Nicd/NiMH Cells 1-15 Cell
- Li-Ion/Li-Po/Li-Fe Cells: 1-6 Cell
- Lead-acid (Pb): 2-20V
- Temperature sensor & USB enable
- Balance: 2-6 Cells
- Case: aluminum
- Display: 16*2 character LCD
The imaxRC B6AC Pro Balance Charger can be bought in our store.
imaxRC B8 Pro Balance Charger
The Imax B8 Pro charger is a very nice charger that will charge any type of battery pack, including NiMh, NiCd, Pb, LiFe, LiPo. It requires a 12v power supply. The B8 Pro is fan cooled and will charger larger size packs than the B6 AC charger.
Features:
- Optimized user interface
- High- power and high-performance circuit
- Individual voltage balance for Lithium batteries inside
- Balance individual cell on discharge
- Suitable for various types of Lithium batteries
- Lithium battery “Fast” and “Storage” mode
- Maximum safety
- Data Store/Load
- Cyclic charging/discharging
- PC based analysis using USB communication
- Built-in fan and higher heat sink performance lead to super cool effect
- Soft touch button
- Multi-use wires
B8 PRO Specification:
- Input voltage: DC 11V-18V
- Charge current: 0.1-7A, 0.1A step
- Discharge current: 0.1-5A, 0.1A step
- Nicd/NiMH Cells: 1-27Cell
- Li-Ion/Li-Po/Li-Fe Cells: 1-8Cell
- Lead-acid (Pb):2-36V
- Temperature sensor & USB enable
- Balance: 2-8Cell
- Case: Aluminium
- Display: 16*2 character LCD
The imaxRC B8 Pro Balance Charger can be bought in our store.
