The Killer Bee Kit 1 contains just the Killer Bee v1, v2, or v2-S kill switch. You must provide the wiring necessary to connect it to the engine’s ignition coil. If you do not know how to make the wiring then you should buy a kit #2, 3, 4, or 5. The Killer Bee is the heart of all kits #1 through #5.
Killer Bee v1 works with all 3 & 4 channel radios.
Killer Bee v2 works with all 2, 3, & 4 channel radios, except Spektrum, Nomadio, Traxxas, and HPI 2.4ghz 2 channel Radios.
Killer Bee v2-S works with Spektrum 2 or 3 channel radios.
The Killer Bee Kit 2 allows you to eliminate the stock kill switch. This kit connects the Killer Bee in your battery box directly to the ignition coil on your engine. The wires are securely soldered to the connectors and then heatshrinked. To kill the engine you just flip off the 3rd channel switch on your transmitter, or turn off your transmitter. This kit includes the Killer Bee v1, v2, v2-S, heat resistant wiring & zip tie.
Killer Bee v1 works with all 3 & 4 channel radios.
Killer Bee v2 works with all 2, 3, & 4 channel radios, except Spektrum, Nomadio, Traxxas, and HPI 2.4ghz 2 channel Radios.
Killer Bee v2-S works with Spektrum 2 or 3 channel radios.
If you select "Boat" type wiring this kit will come with 20" wiring that has a male bullet plug on one wire and a ring terminal on the other wire. The ring terminal bolts to your engine (ground). The male bullet connector plugs into the black wire on the ignition coil.
The Killer Bee Kit 3 comes with wiring that is soldered to the connectors of the CY push button kill switch, and it's heat shrinked and zip tied. This kit is compatible with Zenoah and Chung Yang engines. This kit includes the Killer Bee v1, v2,or v2-S, heat resistant wiring with new CY kill switch & zip tie.
Killer Bee v1 works with all 3 & 4 channel radios.
Killer Bee v2 works with all 2, 3, & 4 channel radios, except Spektrum, Nomadio, Traxxas, and HPI 2.4ghz 2 channel Radios.
Killer Bee v2-S works with Spektrum 2 or 3 channel radios.
The Killer Bee Kit 4 comes with a Killer Bee v1, v2, or v2-S, presoldered heat resistant wiring and new CY push button kill switch, zip tie, remote status LED with 7” wiring for mounting LED in the battery box lid. To mount LED, simply drill a 1/4” hole in the lid, insert the clear LED cover in the hole, and fit the LED into the lens, and add some glue around the base of the LED. The LED will glow on/off and flash, showing the status of the Killer Bee kill switch. If you want, you can substitute the Buzzer in place of the LED.
LED colors to choose from:
Green
Red
Blue
Orange
Killer Bee v1 works with all 3 & 4 channel radios.
Killer Bee v2 works with all 2, 3, & 4 channel radios, except Spektrum, Nomadio, Traxxas, and HPI 2.4ghz 2 channel Radios.
Killer Bee v2-S works with Spektrum 2 or 3 channel radios.
The Killer Bee Kit 5 comes with the Killer Bee v1, v2, or v2-S, presoldered heat resistant wiring and new CY push button kill switch, zip tie, alarm buzzer, remote status LED with 7” wiring for mounting LED in the battery box lid. To mount LED, simply drill a 1/4” hole in the lid, insert the clear LED cover in the hole, and fit the LED into the lens, and add some glue around the base of the LED. The LED will glow on/off and flash, showing the status of the Killer Bee kill switch. Alarm buzzer will sound when engine is killed, reminding you to flip your 3rd channel switch before trying to start the engine. The alarm buzzer will also sound if you have turned off your transmitter power but left the receiver power on, reminding you to turn off your receiver power and prevent fail safe mode from damaging your servo’s. LED colors to choose from:
Green
Red
Blue
Orange
Killer Bee v1 works with all 3 & 4 channel radios.
Killer Bee v2 works with all 2, 3, & 4 channel radios, except Spektrum, Nomadio, Traxxas, and HPI 2.4ghz 2 channel Radios.
Killer Bee v2-S works with Spektrum 2 or 3 channel radios.
The 7" Remote LED makes it easier to see what mode the Killer Bee is in. Includes LED lens. Drill 1/4" hole in battery box lid and insert LED into lens. Add some Shoe Goo on the underside of the lid to secure the LED and lens.
LED colors to choose from: • Green • Red • Blue • Orange
LED status: • LED On - Engine can be started • LED Flashing - Engine killed, no radio reception • LED Off - Engine killed via transmitter
Add the Buzzer to kits 1 through 4 to enable the audible alarm feature of the Killer Bee. The Buzzer will sound when you have left the receiver power on and turned transmitter power off, which will keep you from damaging servo's by leaving the receiver in failsafe mode. The Buzzer will also sound when the engine is killed, reminding you to flip the 3rd channel switch on your transmitter.
This new "plug & play" Light Controller allows you to control multiple sets of LED headlights and tail lights on your RC car. The Killer RC Light Controller goes in between your radio receiver and your servos. Use your 3rd channel to switch through 3 headlight modes; off, low beam, and high beam. This light controller is compatible with any 3 channel radio. The Killer RC light controller can also power a set of 2 tail/brake lights. When you apply the brakes on your transmitter your tail lights will light up and become brake lights. You can also make your tail lights function as turn signals. As you steer the car the tail lights will flash which ever direction you are turning. This feature can be disabled. The Killer RC light controller also has an always-on marker light output, which can be used for UnderGlow lights or whatever you want. Connect a v2 or v2-S Killer Bee to the Aux output on the light controller, and then you can kill the engine by turning off the transmitter power. With 4 channel radios the setup is a little different, so be sure to watch the light controller videos on our video page. The Killer RC light controller can also be used with 2 channel radios but the headlights will always be constantly On until the receiver power switch is turned Off. Another cool feature we have added is that the headlights will automatically start flashing when your battery voltage gets low (4.3v), alerting you that you need to recharge the battery pack. This light controller operates on 4 to 12 volts, but whatever voltage your battery is, that is what the light controller will put out to your LED lights. Six volts is the usual application. This light controller is compact in size, doesn't get hot, and can be used on many gas, nitro, and electric RCs. The Killer RC light controller works best with Ramtech brand headlights, and Killer RC brand tail lights.
Now it's easy to add tail lights to your HPI Baja 5T using the stock light brackets. This kit uses high quality LEDs that will last for thousands of hours. These lights operate on 4 to 8.5 volts. Each light board only pulls 70ma, which means that a 3,000mAh battery could power a pair of these tail lights for over 21 hours. Includes 6 mounting screws and 6 black plastic washers to hold the circuit boards in place. The wiring is 32 inches (81cm) long. Red is the only color available for now. After installation it is a good idea to coat the back of the LED circuit board with some Shoe Goo or silicone to help protect it from water. These tail lights work perfectly with the new Killer RC Light Controller. Sold in pairs.
2-Way Splitter Cable: Two female to One male JR/Futaba/Hitec plug. 4-Way Splitter Cable: 6" long. One male to four female. JR/Hitec style plug. Gold plated contacts. 3 conductor. 22 AWG.
This pair (2) of 18" long extension cables has gold plated male and female Futaba connectors. These cables can be used to extend battery or light wiring, etc. 22awg, 2 conductor.
Servos and wiring can short-circuit, which can damage your expensive radio receiver, battery, and even catch the radio box on fire. The Killer RC inline fuse will prevent this. Just plug it inline between the battery and your on/off switch. Comes with 15A fuse. Works with most any gas or nitro electrical system. In the event of a blown fuse loosing battery power to the receiver can cause a runaway vehicle, so we recommend that you use a Killer Bee kill switch to stop any potential runaways.
The new Suspension Limiting Killer Kables from Killer RC will dramatically prolong the life of your HPI Baja's shocks and drive shafts. Without limiting cables the Baja's suspension will over-extend, causing the shock pistons to bottom out, which damages the piston, seals, and rod end. An over-extending suspension can also cause damage to your drive shaft pins and cups. With Killer Kables you can spend more time running your Baja and less time repairing it. Killer Kables fit on the HPI Baja RTR, SS, and 5T that have FLM, RPM, or stock HPI suspension arms. Killer Kables may also work on other aftermarket arms that have sway bar provisions. Killer Kables are made in the USA from the highest quality, aircraft grade, coated steel cable, and hydraulically crimped stainless steel eyelets. Be sure to mount cables straight from eyelet to eyelet. Check this forum thread for installation info. Get installation info here. An installation video is here.
Color:
$ 29.00
×
Killer Kable Pro Kit for HPI Baja
SPECIAL FOR LIMITED TIME ONLY! - FREE BAJA REAR TURNBUCKLES WITH PURCHASE OF A KILLER KABLE PRO KIT!!!
The new Killer Kable Pro Kit comes with 8 pairs of different length suspension limiting cables and 2 packs of fastening hardware, which is enough for 2 or more Bajas. With this new Pro kit you will have more control over the suspension travel and ride height of your Baja. Use the longer cables to get maximum suspension travel off-road, or use shorter cables to lower your Baja for maximum stability on-road. You can mix and match different lengths of cables to make your Baja handle how you want it to. You can even put shorter cables on one side of the car to help control body-roll when racing on oval tracks. The Killer Kables also prevent your suspension from over-traveling, saving wear & tear on your drive shaft cups, shock pistons, and shock shaft rod ends. The Killer Kables are made from aircraft grade steel cable that is rated to support 500 lb loads. The hydraulically crimped eyelets are stainless steel. The included hardware contains hardened 12.9 grade bolts.
WIth these new Killer Kables for the Traxxas Slash you will prevent shock damage, and keep driveshafts from popping out of the drive cups. Installation is easy.
The Killer RC Rear Turnbuckle Kit includes two polished billet aluminum spacers, and two heat-treated alloy steel turnbuckles. These high tensile alloy steel turnbuckles are specially heat treated, giving them greater strength than titanium or stainless steel. Then when you add the aluminum spacers you have a setup that is many times tougher than the stock setup. The aluminum spacers simply work by spreading out the forces to a larger area on the end of the arm and ball end. Installation is easy. Just screw the turnbuckle into the arm, slide the spacer over the turnbuckle and tighten the ball end tight up against it. You should not be able to move or spin the spacer. The aluminum spacers will fit overtop of PhatDad turnbuckles. They will also fit overtop of Fast Eddy pro turnbuckles if you drill open the spacers' a little bit. For spacer length choose 12mm (stock camber), 9.5mm, or 14.8mm spacers (great for the FLM extended arm kit).
Hyperion LiFeP04 Transmitter Battery Pack & Adapter Cable These new LiFe packs are a great for powering the Futaba 4PK, 3PK, 3PM, or Airtronics M11 . If you don't have a LiFe compatible charger you can still use these packs. These LiFe packs have a built-in Protection Circuit that allows you to charge the pack with a standard NiMh wall plug charger, like the charger that comes with the Futaba 4PK. This pack comes with a Hyperion/Polyquest balance tap.
This pack features: - More capacity per gram than NiMh. - Almost no "self discharge", so your radio is always ready to go even weeks after charging. - Superior voltage performance under load. - Faster charge time. - Safer and more convenient than LiPo.
Includes custom Killer RC adapter cable with JR/Futaba style plug.
This balance board adapter works with Hyperion/Hyperion/JST-XH balance taps on LiFe and LiPo battery packs. See this forum thread for more info on how you can use this balance board.
The Imax B6 AC Pro charger is a very nice charger that will charge any type of battery pack, including NiMh, NiCd, Pb, LiFe, LiPo. It works on 100 - 250 vac wall outlet, or 12v power supply. Multi-use wires are provided with the B6AC. You can charge and discharge your battery easily with these wires.
B6AC PRO Specification: - lnputYoltage: DC 11V-18V, AC 100V-250V - Charge current: 0.1-5A, 0.1A step - Discharge current 0.1-1A, 0.1A step - Nicd/NiMH Cells 1-15 Cell - Li-Ion/Li-Po/Li-Fe Cells: 1-6 Cell - Lead-acid (Pb): 2-20V - Temperature sensor & USB enable - Balance: 2-6 Cells - Case: aluminum - Display: 16*2 character LCD
The Imax B8 Pro charger is a very nice charger that will charge any type of battery pack, including NiMh, NiCd, Pb, LiFe, LiPo. It requires a 12v power supply. The B8 Pro is fan cooled and will charger larger size packs than the B6 AC charger.
Features: - Optimized user interface - High- power and high-performance circuit - Individual voltage balance for Lithium batteries inside - Balance individual cell on discharge - Suitable for various types of Lithium batteries - Lithium battery “Fast” and “Storage” mode - Maximum safety - Data Store/Load - Cyclic charging/discharging - PC based analysis using USB communication - Built-in fan and higher heat sink performance lead to super cool effect - Soft touch button - Multi-use wires
B8 PRO Specification: - Input voltage: DC 11V-18V - Charge current: 0.1-7A, 0.1A step - Discharge current: 0.1-5A, 0.1A step - Nicd/NiMH Cells: 1-27Cell - Li-Ion/Li-Po/Li-Fe Cells: 1-8Cell - Lead-acid (Pb):2-36V - Temperature sensor & USB enable - Balance: 2-8Cell - Case: Aluminium - Display: 16*2 character LCD
Shoe Goo is great for securing the remote mount LED that comes with kill switch kit #4 and #5. Just put a glob of it around the underside of the LED and wires. Let it sit for an hour. It will cure to a firm rubbery texture. It bonds to almost any surface, and has many uses on R/Cs.
This kit works just like our regular kit #3 (with Killer Bee v1) except the Remote LED output is not operational. The red Deans plugs were accidentally soldered in backwards. This doesn't affect the main operation of the kill switch. The kill switch still kills the engine like usual. The small built-in LED on the circuit board, and the buzzer output still operate properly. The Remote LED output is the only thing that is not operational. You can still add the optional buzzer to this kit to get audible confirmation of what mode the Killer Bee is in. If you don't need the remote 7" LED lead then this is your chance to get a great deal. Supply is limited. This kit comes with a v1 Killer Bee, not v2. Killer Bee v1 works with all 3 & 4 channel radios.
$ 50.00
×
Killer RC Embroidered FlexFit Hat
SPECIAL FOR LIMITED TIME ONLY! - FREE 2-WAY SPLITTER CABLE WITH PURCHASE OF A KILLER RC HAT!!!
